Original price
Rs. 3,331.00
-
Original price
Rs. 3,331.00
Original price
Rs. 3,331.00
Current price
Rs. 1,813.00
Rs. 1,813.00
-
Rs. 1,813.00
Current price
Rs. 1,813.00
| /
7–9.8IN HEIGHT • 5–45° TILT • WEIGHTED BASE
UGREEN Height-Adjustable Desk Phone Stand, Black (80194)
Overview
UGREEN 80194 raises a compatible smartphone above the desk for hands-free calls, reading, streaming, recipes and glanceable notifications. telescopic support height from approximately 7 to 9.8 inches (178–249mm), with an approximately 5–45° tilting cradle; portrait or landscape placement is done by lifting and replacing the phone. The construction is aluminium-alloy support rod, durable PC/ABS housing, galvanized internal base plate and silicone contact surfaces. Below: fit, setup, stability and safety boundaries so the product is easy to choose and use responsibly.
SKU 80194Desk Phone HolderBlackPassive holder
SKU 80194 visual: Product view: the weighted pedestal, telescopic support and padded cradle of UGREEN 80194.
Key features
Holder type
Desk Phone Holder. raises a compatible smartphone above the desk for hands-free calls, reading, streaming, recipes and glanceable notifications.
Fit boundary
smartphones and compact devices that sit fully inside the two cradle hooks; confirm the complete phone-and-case dimensions because the gallery does not state a universal width or load limit.
Adjustment
telescopic support height from approximately 7 to 9.8 inches (178–249mm), with an approximately 5–45° tilting cradle; portrait or landscape placement is done by lifting and replacing the phone.
Mounting method
freestanding tabletop base with internal galvanized weight and four anti-slip feet; use only on a clean, dry, flat and level surface.
SKU 80194 visual: Contact protection: silicone covers the phone support area, while four feet help the weighted base resist sliding.
Measure before ordering
Phone and tablet names are only examples. Physical compatibility is controlled by screen and body size, total thickness, weight, case shape, camera bump, accessories and the way the device meets the support points.
Measure the complete setup
smartphones and compact devices that sit fully inside the two cradle hooks; confirm the complete phone-and-case dimensions because the gallery does not state a universal width or load limit. Screen size alone does not describe case thickness, camera bump, grip accessories or total weight.
Check the support points
Both lower hooks and the padded back surface must contact the device securely. Remove a wallet, ring, battery case or pop-out grip if it interferes.
Choose a stable position
Open or assemble the stand on a clean, flat and level surface. Start with a low, slightly rearward angle, place the device centrally and increase height or tilt only after checking balance.
Test before normal use
Gently tap the screen and check every hinge, clamp, base, adhesive bond or vent clip. Stop if the device creeps, tips, releases or makes the mounting surface flex.
SKU 80194 visual: Height check: the support extends from about 7 to 9.8 inches; stability should be rechecked after raising it.
Adjustment and viewing guide
Mechanism: telescopic support height from approximately 7 to 9.8 inches (178–249mm), with an approximately 5–45° tilting cradle; portrait or landscape placement is done by lifting and replacing the phone.
Adjust unloaded whenever practical. Support the device with one hand, move the mechanism with the other and stop at its natural limit. A firm hinge is normal; forcing it can damage the joint or make the base slip.
Stability principle: raising, extending or moving a device forward increases leverage. Heavier devices should stay lower, closer to the base or clamp, and slightly tilted back.
SKU 80194 visual: Viewing adjustment: the cradle tilts from approximately 5° to 45°; reposition the phone itself for portrait or landscape use.
Use scenarios
Calls and meetings
Raise the camera closer to a natural sightline and keep the device hands-free. Use headphones when privacy or echo control matters.
Video and learning
Place the screen in portrait or landscape for tutorials, online classes, streaming and reference material.
Desk companion
Keep messages, OTPs, timers, music controls or a second-screen reference visible beside a computer.
Recipes and hobbies
Follow instructions with cleaner hands, but keep the holder away from water, steam, oil, heat and unstable counter edges.
SKU 80194 visual: Hands-free scenario: raised desk positioning can improve the camera sightline for calls and streaming.
Setup and usability guidance
Step 1: Unfold the stand or lower it to its most stable starting position.
Step 2: Place it on a clean, flat, dry and level surface away from edges.
Step 3: Adjust the hinge, height or rotation with two hands before loading a larger device.
Step 4: Centre the phone or tablet across the padded cradle in portrait or landscape.
Step 5: Check case clearance, cable access and balance with a gentle screen tap.
Step 6: Readjust to a lower position if typing, drawing or a heavy device causes movement.
Best practice: Open or assemble the stand on a clean, flat and level surface. Start with a low, slightly rearward angle, place the device centrally and increase height or tilt only after checking balance.
SKU 80194 visual: Charging access: the open lower cradle lets a separate compatible cable reach the phone without being pinched.
Mounting surface, stability and environment
Mounting method: freestanding tabletop base with internal galvanized weight and four anti-slip feet; use only on a clean, dry, flat and level surface.
Flat and clean contact
Dust, oil, grit and moisture reduce friction and can scratch surfaces. Clean and dry every contact area before installation.
Keep away from edges
Position the loaded device where a slip or release will not send it onto a person, floor, sink, cooker, keyboard or glass object.
Touch gently
Use lighter taps or support the device for typing, drawing and gaming. A holder designed for viewing is not always a rigid typing platform.
Recheck regularly
Temperature, vibration, repeated adjustment and normal wear can change grip. Inspect the mount, pads and device position before each important use.
SKU 80194 visual: Base construction: the internal weighted plate and anti-slip feet are designed for a clean, dry and level desktop.
Compatible devices and systems
Physical class: smartphones and compact devices that sit fully inside the two cradle hooks; confirm the complete phone-and-case dimensions because the gallery does not state a universal width or load limit.
Apple devices
Compatible iPhone or iPad examples may fit only when their complete size, weight and case remain within the stated physical limits.
Android devices
Samsung Galaxy, Google Pixel, OnePlus, Xiaomi, Redmi, realme and other phones/tablets are assessed by measurements—not brand alone.
E-readers and handhelds
A Kindle, e-reader, Switch or similar device may fit only if all support points engage and the complete device stays inside every size and load limit.
Case caveat
A protective case can increase thickness, move the centre of gravity and cover the charging opening. Measure it installed, not separately.
What this product does
Raises a compatible smartphone above the desk for hands-free calls, reading, streaming, recipes and glanceable notifications.
Uses the documented desk phone holder mechanism for hands-free physical support.
Provides the adjustment: telescopic support height from approximately 7 to 9.8 inches (178–249mm), with an approximately 5–45° tilting cradle; portrait or landscape placement is done by lifting and replacing the phone.
Uses the mounting method: freestanding tabletop base with internal galvanized weight and four anti-slip feet; use only on a clean, dry, flat and level surface.
Protects covered contact areas with the specified silicone, rubber or soft pads; these reduce—not eliminate—the possibility of marks.
What this product does not do
no maximum load or case-thickness figure; not a tablet floor stand, clamp, adhesive mount, magnetic mount or charging device.
It does not include MagSafe, wireless charging, a battery, powered USB port or motor unless explicitly stated—which this SKU does not.
It does not make every phone case, tablet, furniture edge, wall finish, air vent or vehicle compatible.
It does not guarantee zero wobble during touch, typing, drawing, rough roads or fully extended use.
It is not safety equipment and should not suspend a device where release could cause injury or serious damage.
What to do
Measure first
Check the complete device and case against every stated size, thickness, opening and load limit.
Adjust with two hands
Support the device or unload the holder before moving a firm hinge, rail, spring arm, clamp or rotating base.
Route cables safely
Leave slack at the connector, avoid sharp bends and keep cables away from hinges, springs, vehicle controls and walking paths.
Inspect the setup
Check screws, pads, clips, clamps, adhesive edges and device seating before use and after relocation or temperature change.
What not to do
Do not exceed limits
Do not guess load capacity, case fit, clamp thickness, vent compatibility or adhesive reuse beyond the values stated here.
Do not force movement
Stop when a hinge, clamp or rail reaches its natural limit. Do not use tools for extra leverage unless the supplied assembly step requires them.
Do not use near hazards
Avoid flames, hot cookware, wet areas, unstable shelves, traffic controls and positions directly above people or breakables.
Do not trust a partial grip
Both device and mount must be fully seated. A phone caught by one hook, a clamp on a rounded edge or a clip halfway onto a vent is unsafe.
Warnings and limitations
Pinch points: keep fingers, hair, cables and loose clothing clear of hinges, springs, telescopic rails and clamp mechanisms.
Heat and moisture: keep the holder and device away from flames, hot cookware, direct heaters, steam, sinks, rain and pooled liquid.
Children and pets: this is not a toy. Keep small hardware and loaded devices out of reach and avoid trailing cables.
Inspection: stop using the product if a hinge loosens, pad detaches, plastic cracks, metal bends, adhesive lifts, clamp slips or vent blade deforms.
Technical specifications
Brand / SKU
UGREEN 80194
Model / type
Desk Phone Holder
Colour
Black
Primary use
raises a compatible smartphone above the desk for hands-free calls, reading, streaming, recipes and glanceable notifications
Device fit
smartphones and compact devices that sit fully inside the two cradle hooks; confirm the complete phone-and-case dimensions because the gallery does not state a universal width or load limit
Adjustment
telescopic support height from approximately 7 to 9.8 inches (178–249mm), with an approximately 5–45° tilting cradle; portrait or landscape placement is done by lifting and replacing the phone
Mounting method
freestanding tabletop base with internal galvanized weight and four anti-slip feet; use only on a clean, dry, flat and level surface
Materials
aluminium-alloy support rod, durable PC/ABS housing, galvanized internal base plate and silicone contact surfaces
Height adjustment
Approximately 7–9.8in / 178–249mm
Cradle angle
Approximately 5–45°
Base weight stated on page
Approximately 7.8oz / 221g
Orientation
Portrait or landscape by repositioning the device
Charging access
Open lower cradle for a separate compatible cable
Charging / electronics
None; passive mechanical holder
Package contents
1 × UGREEN 80194 desk phone holder (phone, cable and charger not included)
Package contents
Troubleshooting
Device tips forward
Lower the height or arm, tilt the device back, centre it over the support and remove a heavy case/accessory. Stop if the stated fit or load limit is exceeded.
Holder slides or rotates
Unload it, clean and dry contact pads, retighten only as instructed and move to a firmer, flatter mounting point.
Case will not sit fully
Measure total thickness and width. Remove a wallet, grip, battery or rugged case rather than forcing the device into shallow hooks.
Cable does not fit
Try a slimmer compatible connector and route it without tension. The access opening does not guarantee every plug shape or port location.
Hinge feels too firm
Unload the stand and move the joint slowly with two hands. Do not apply oil, heat or extra tools; stop if the housing separates or metal bends.
Mounting surface looks marked
Remove the device immediately. Do not keep tightening or loading the mount; follow the furniture, wall or vehicle manufacturer’s care guidance.
Product-specific FAQ
What is UGREEN 80194 designed to do?
It raises a compatible smartphone above the desk for hands-free calls, reading, streaming, recipes and glanceable notifications. It is a passive mechanical holder, not a powered accessory.
Which phones or tablets fit?
smartphones and compact devices that sit fully inside the two cradle hooks; confirm the complete phone-and-case dimensions because the gallery does not state a universal width or load limit. Measure the complete device with its normal case and accessories before ordering.
Can I use a protective case?
Often yes when the combined device and case remain within every stated size, thickness, weight and cradle limit. Thick rugged, wallet, battery, keyboard and grip cases may need removal.
Does it charge the device?
No. The holder contains no charging electronics, battery or power supply. Any charging opening only provides space for a separate compatible cable, charger and socket.
Does it use MagSafe or magnets?
No magnetic attachment is claimed for this SKU. The device is supported mechanically by its cradle, clamp, base, adhesive shelf or vent-mounted structure as described above.
Can I use it in portrait and landscape?
Yes. Lift the device and place it back across the hooks; the cradle itself does not automatically rotate.
Will it stay completely still when I touch the screen?
No freestanding, articulated, adhesive, clamp or vent holder can guarantee zero movement. Use a lower, centred position and support the device during firm typing, drawing or repeated tapping.
What surface or mounting point should I use?
freestanding tabletop base with internal galvanized weight and four anti-slip feet; use only on a clean, dry, flat and level surface. Avoid fragile, dirty, wet, textured, loose or heat-damaged surfaces.
What should I avoid?
no maximum load or case-thickness figure; not a tablet floor stand, clamp, adhesive mount, magnetic mount or charging device. Do not exceed stated dimensions or place the loaded holder where a fall could injure someone or damage another object.
How should I clean it?
Remove the device first. Wipe hard surfaces with a soft, slightly damp cloth, then dry completely. Do not soak hinges, springs, adhesive, clamp pads or vent clips and do not use solvents or abrasives.
What is included?
1 × UGREEN 80194 desk phone holder (phone, cable and charger not included).
model check before ordering
Match UGREEN SKU 80194, the desk phone holder, its fit boundary, mounting method and adjustment mechanism. Similar UGREEN holders can use different hinges, clamp spans, device limits, adhesives or vehicle fittings.
