Original price
Rs. 999.00
-
Original price
Rs. 999.00
Original price
Rs. 999.00
Current price
Rs. 639.00
Rs. 639.00
-
Rs. 639.00
Current price
Rs. 639.00
| /
3M ADHESIVE • 14MM CRADLE • 24H CURE
UGREEN LP108 Adhesive Wall-Mount Phone Holder, White (30394)
Overview
UGREEN 30394 creates a compact fixed resting shelf for a compatible phone beside a socket, bed, desk or workstation while a separate cable charges it. fixed wall shelf with no angle, height, rotation or width adjustment; placement must be chosen carefully before exposing the adhesive. The construction is white rigid holder body, 3M adhesive pad, soft non-slip phone contact areas and a rear cable-winding spool. Below: fit, setup, stability and safety boundaries so the product is easy to choose and use responsibly.
SKU 30394LP108 Wall HolderWhitePassive holder
SKU 30394 visual: Product view: UGREEN LP108 30394 is a passive white wall cradle with a pre-applied adhesive mounting pad.
Key features
Holder type
LP108 Wall Holder. creates a compact fixed resting shelf for a compatible phone beside a socket, bed, desk or workstation while a separate cable charges it.
Fit boundary
most smartphones whose complete phone-and-case thickness is no more than approximately 14mm and that can rest securely across the 117mm-wide shelf.
Adjustment
fixed wall shelf with no angle, height, rotation or width adjustment; placement must be chosen carefully before exposing the adhesive.
Mounting method
single-use 3M adhesive pad on a clean, dry, smooth, flat, sealed vertical surface; press firmly and wait at least 24 hours before loading.
SKU 30394 visual: Compact details: silicone contact points cushion the phone and the rear spool stores slack from a separate cable.
Measure before ordering
Phone and tablet names are only examples. Physical compatibility is controlled by screen and body size, total thickness, weight, case shape, camera bump, accessories and the way the device meets the support points.
Measure the complete setup
most smartphones whose complete phone-and-case thickness is no more than approximately 14mm and that can rest securely across the 117mm-wide shelf. Screen size alone does not describe case thickness, camera bump, grip accessories or total weight.
Check the support points
Both lower hooks and the padded back surface must contact the device securely. Remove a wallet, ring, battery case or pop-out grip if it interferes.
Choose a stable position
Install only after a dry fit. Place the holder where the phone, charger and cable can reach without tension, then allow the adhesive to cure for a full 24 hours.
Test before normal use
Gently tap the screen and check every hinge, clamp, base, adhesive bond or vent clip. Stop if the device creeps, tips, releases or makes the mounting surface flex.
Adjustment and viewing guide
Mechanism: fixed wall shelf with no angle, height, rotation or width adjustment; placement must be chosen carefully before exposing the adhesive.
Adjust unloaded whenever practical. Support the device with one hand, move the mechanism with the other and stop at its natural limit. A firm hinge is normal; forcing it can damage the joint or make the base slip.
Stability principle: raising, extending or moving a device forward increases leverage. Heavier devices should stay lower, closer to the base or clamp, and slightly tilted back.
Use scenarios
Bedside charging
Keep the phone off the floor and reduce cable clutter beside a suitable socket.
Desk or workstation
Create a fixed resting place without occupying the desktop.
Entry or utility area
Use for a lightweight phone reference on a suitable smooth sealed surface.
Cable storage
Wind only loose excess cable; never make tight turns or hang the phone by its connector.
SKU 30394 visual: Socket-side scenario: the cradle can keep a supported phone off the floor while a separate charger and cable are used.
Setup and usability guidance
Step 1: Dry-fit the phone, cable and charger location before removing the adhesive liner.
Step 2: Clean the smooth sealed surface to remove dust, oil and moisture; allow it to dry completely.
Step 3: Peel the liner without touching the adhesive, align the holder level and press firmly and evenly for at least 30 seconds.
Step 4: Leave the holder unloaded for at least 24 hours.
Step 5: Place the phone gently into the cradle and confirm the cable has slack rather than pulling on the shelf.
Step 6: Inspect the bond regularly; remove the phone immediately if an edge lifts or the wall finish changes.
Best practice: Install only after a dry fit. Place the holder where the phone, charger and cable can reach without tension, then allow the adhesive to cure for a full 24 hours.
SKU 30394 visual: Installation sequence: clean and dry the surface, remove the liner, press the holder level, then leave it unloaded for 24 hours.
Mounting surface, stability and environment
Mounting method: single-use 3M adhesive pad on a clean, dry, smooth, flat, sealed vertical surface; press firmly and wait at least 24 hours before loading.
Flat and clean contact
Dust, oil, grit and moisture reduce friction and can scratch surfaces. Clean and dry every contact area before installation.
Keep away from edges
Position the loaded device where a slip or release will not send it onto a person, floor, sink, cooker, keyboard or glass object.
Touch gently
Use lighter taps or support the device for typing, drawing and gaming. A holder designed for viewing is not always a rigid typing platform.
Recheck regularly
Temperature, vibration, repeated adjustment and normal wear can change grip. Inspect the mount, pads and device position before each important use.
SKU 30394 visual: Adhesive attachment: the broad rear pad requires a clean, dry, smooth and sound surface for reliable bonding.
Compatible devices and systems
Physical class: most smartphones whose complete phone-and-case thickness is no more than approximately 14mm and that can rest securely across the 117mm-wide shelf.
Apple devices
Compatible iPhone or iPad examples may fit only when their complete size, weight and case remain within the stated physical limits.
Android devices
Samsung Galaxy, Google Pixel, OnePlus, Xiaomi, Redmi, realme and other phones/tablets are assessed by measurements—not brand alone.
E-readers and handhelds
A Kindle, e-reader, Switch or similar device may fit only if all support points engage and the complete device stays inside every size and load limit.
Case caveat
A protective case can increase thickness, move the centre of gravity and cover the charging opening. Measure it installed, not separately.
What this product does
Creates a compact fixed resting shelf for a compatible phone beside a socket, bed, desk or workstation while a separate cable charges it.
Uses the documented lp108 wall holder mechanism for hands-free physical support.
Provides the adjustment: fixed wall shelf with no angle, height, rotation or width adjustment; placement must be chosen carefully before exposing the adhesive.
Uses the mounting method: single-use 3M adhesive pad on a clean, dry, smooth, flat, sealed vertical surface; press firmly and wait at least 24 hours before loading.
Protects covered contact areas with the specified silicone, rubber or soft pads; these reduce—not eliminate—the possibility of marks.
SKU 30394 visual: Desk-wall scenario: a fixed cradle can keep the phone visible and reduce cable clutter beside a computer.
What this product does not do
not a charger, tablet shelf, bathroom wet-area mount or reusable/repositionable adhesive system; removal can mark delicate paint, wallpaper or finishes.
It does not include MagSafe, wireless charging, a battery, powered USB port or motor unless explicitly stated—which this SKU does not.
It does not make every phone case, tablet, furniture edge, wall finish, air vent or vehicle compatible.
It does not guarantee zero wobble during touch, typing, drawing, rough roads or fully extended use.
It is not safety equipment and should not suspend a device where release could cause injury or serious damage.
What to do
Measure first
Check the complete device and case against every stated size, thickness, opening and load limit.
Adjust with two hands
Support the device or unload the holder before moving a firm hinge, rail, spring arm, clamp or rotating base.
Route cables safely
Leave slack at the connector, avoid sharp bends and keep cables away from hinges, springs, vehicle controls and walking paths.
Inspect the setup
Check screws, pads, clips, clamps, adhesive edges and device seating before use and after relocation or temperature change.
What not to do
Do not exceed limits
Do not guess load capacity, case fit, clamp thickness, vent compatibility or adhesive reuse beyond the values stated here.
Do not force movement
Stop when a hinge, clamp or rail reaches its natural limit. Do not use tools for extra leverage unless the supplied assembly step requires them.
Do not use near hazards
Avoid flames, hot cookware, wet areas, unstable shelves, traffic controls and positions directly above people or breakables.
Do not trust a partial grip
Both device and mount must be fully seated. A phone caught by one hook, a clamp on a rounded edge or a clip halfway onto a vent is unsafe.
Warnings and limitations
Adhesive safety: do not install on textured wallpaper, loose paint, plaster, damp surfaces or valuable delicate finishes. Adhesive is not guaranteed reusable and removal can mark the surface.
Pinch points: keep fingers, hair, cables and loose clothing clear of hinges, springs, telescopic rails and clamp mechanisms.
Heat and moisture: keep the holder and device away from flames, hot cookware, direct heaters, steam, sinks, rain and pooled liquid.
Children and pets: this is not a toy. Keep small hardware and loaded devices out of reach and avoid trailing cables.
Inspection: stop using the product if a hinge loosens, pad detaches, plastic cracks, metal bends, adhesive lifts, clamp slips or vent blade deforms.
Technical specifications
Brand / SKU
UGREEN 30394
Model / type
LP108 Wall Holder
Colour
White
Primary use
creates a compact fixed resting shelf for a compatible phone beside a socket, bed, desk or workstation while a separate cable charges it
Device fit
most smartphones whose complete phone-and-case thickness is no more than approximately 14mm and that can rest securely across the 117mm-wide shelf
Adjustment
fixed wall shelf with no angle, height, rotation or width adjustment; placement must be chosen carefully before exposing the adhesive
Mounting method
single-use 3M adhesive pad on a clean, dry, smooth, flat, sealed vertical surface; press firmly and wait at least 24 hours before loading
Materials
white rigid holder body, 3M adhesive pad, soft non-slip phone contact areas and a rear cable-winding spool
Holder dimensions shown
Approximately 117 × 64 × 14mm
Maximum phone + case thickness
Approximately 14mm
Installation
Single-use 3M self-adhesive pad
Curing time
At least 24 hours before loading
Cable management
Integrated rear winding spool
Built-in charging
None
Charging / electronics
None; passive mechanical holder
Package contents
1 × UGREEN LP108 / 30394 wall phone holder with pre-applied adhesive pad
Package contents
Troubleshooting
Device tips forward
Lower the height or arm, tilt the device back, centre it over the support and remove a heavy case/accessory. Stop if the stated fit or load limit is exceeded.
Holder slides or rotates
Unload it, clean and dry contact pads, retighten only as instructed and move to a firmer, flatter mounting point.
Case will not sit fully
Measure total thickness and width. Remove a wallet, grip, battery or rugged case rather than forcing the device into shallow hooks.
Cable does not fit
Try a slimmer compatible connector and route it without tension. The access opening does not guarantee every plug shape or port location.
Hinge feels too firm
Unload the stand and move the joint slowly with two hands. Do not apply oil, heat or extra tools; stop if the housing separates or metal bends.
Mounting surface looks marked
Remove the device immediately. Do not keep tightening or loading the mount; follow the furniture, wall or vehicle manufacturer’s care guidance.
Product-specific FAQ
What is UGREEN 30394 designed to do?
It creates a compact fixed resting shelf for a compatible phone beside a socket, bed, desk or workstation while a separate cable charges it. It is a passive mechanical holder, not a powered accessory.
Which phones or tablets fit?
most smartphones whose complete phone-and-case thickness is no more than approximately 14mm and that can rest securely across the 117mm-wide shelf. Measure the complete device with its normal case and accessories before ordering.
Can I use a protective case?
Often yes when the combined device and case remain within every stated size, thickness, weight and cradle limit. Thick rugged, wallet, battery, keyboard and grip cases may need removal.
Does it charge the device?
No. The holder contains no charging electronics, battery or power supply. Any charging opening only provides space for a separate compatible cable, charger and socket.
Does it use MagSafe or magnets?
No magnetic attachment is claimed for this SKU. The device is supported mechanically by its cradle, clamp, base, adhesive shelf or vent-mounted structure as described above.
Can I use it in portrait and landscape?
The wall shelf is primarily a fixed resting cradle. Landscape fit depends on the phone dimensions and cable position; check both before loading.
Will it stay completely still when I touch the screen?
No freestanding, articulated, adhesive, clamp or vent holder can guarantee zero movement. Use a lower, centred position and support the device during firm typing, drawing or repeated tapping.
What surface or mounting point should I use?
single-use 3M adhesive pad on a clean, dry, smooth, flat, sealed vertical surface; press firmly and wait at least 24 hours before loading. Avoid fragile, dirty, wet, textured, loose or heat-damaged surfaces.
What should I avoid?
not a charger, tablet shelf, bathroom wet-area mount or reusable/repositionable adhesive system; removal can mark delicate paint, wallpaper or finishes. Do not exceed stated dimensions or place the loaded holder where a fall could injure someone or damage another object.
How should I clean it?
Remove the device first. Wipe hard surfaces with a soft, slightly damp cloth, then dry completely. Do not soak hinges, springs, adhesive, clamp pads or vent clips and do not use solvents or abrasives.
Match UGREEN SKU 30394, the lp108 wall holder, its fit boundary, mounting method and adjustment mechanism. Similar UGREEN holders can use different hinges, clamp spans, device limits, adhesives or vehicle fittings.
