UGREEN LP108 Adhesive Wall-Mount Phone Holder, White (30394)
Overview
UGREEN 30394 creates a compact fixed resting shelf for a compatible phone beside a socket, bed, desk or workstation while a separate cable charges it. fixed wall shelf with no angle, height, rotation or width adjustment; placement must be chosen carefully before exposing the adhesive. The construction is white rigid holder body, 3M adhesive pad, soft non-slip phone contact areas and a rear cable-winding spool. Below: fit, setup, stability and safety boundaries so the product is easy to choose and use responsibly.
- 3M ADHESIVE • 14MM CRADLE • 24H CURE
- SKU 30394
- LP108 Wall Holder
- White
- Passive holder
What it does well.
Key features
Holder type. LP108 Wall Holder. creates a compact fixed resting shelf for a compatible phone beside a socket, bed, desk or workstation while a separate cable charges it.
Fit boundary. most smartphones whose complete phone-and-case thickness is no more than approximately 14mm and that can rest securely across the 117mm-wide shelf.
Adjustment. fixed wall shelf with no angle, height, rotation or width adjustment; placement must be chosen carefully before exposing the adhesive.
Mounting method. single-use 3M adhesive pad on a clean, dry, smooth, flat, sealed vertical surface; press firmly and wait at least 24 hours before loading.
Measure before ordering
Phone and tablet names are only examples. Physical compatibility is controlled by screen and body size, total thickness, weight, case shape, camera bump, accessories and the way the device meets the support points.
Measure the complete setup. most smartphones whose complete phone-and-case thickness is no more than approximately 14mm and that can rest securely across the 117mm-wide shelf. Screen size alone does not describe case thickness, camera bump, grip accessories or total weight.
Check the support points. Both lower hooks and the padded back surface must contact the device securely. Remove a wallet, ring, battery case or pop-out grip if it interferes.
Choose a stable position. Install only after a dry fit. Place the holder where the phone, charger and cable can reach without tension, then allow the adhesive to cure for a full 24 hours.
Test before normal use. Gently tap the screen and check every hinge, clamp, base, adhesive bond or vent clip. Stop if the device creeps, tips, releases or makes the mounting surface flex.
Adjustment and viewing guide
Mechanism: fixed wall shelf with no angle, height, rotation or width adjustment; placement must be chosen carefully before exposing the adhesive.
Adjust unloaded whenever practical. Support the device with one hand, move the mechanism with the other and stop at its natural limit. A firm hinge is normal; forcing it can damage the joint or make the base slip.
Stability principle: raising, extending or moving a device forward increases leverage. Heavier devices should stay lower, closer to the base or clamp, and slightly tilted back.
Use scenarios
Bedside charging. Keep the phone off the floor and reduce cable clutter beside a suitable socket.
Desk or workstation. Create a fixed resting place without occupying the desktop.
Entry or utility area. Use for a lightweight phone reference on a suitable smooth sealed surface.
Cable storage. Wind only loose excess cable; never make tight turns or hang the phone by its connector.
Setup and usability guidance
Best practice: Install only after a dry fit. Place the holder where the phone, charger and cable can reach without tension, then allow the adhesive to cure for a full 24 hours.
- Step 1: Dry-fit the phone, cable and charger location before removing the adhesive liner.
- Step 2: Clean the smooth sealed surface to remove dust, oil and moisture; allow it to dry completely.
- Step 3: Peel the liner without touching the adhesive, align the holder level and press firmly and evenly for at least 30 seconds.
- Step 4: Leave the holder unloaded for at least 24 hours.
- Step 5: Place the phone gently into the cradle and confirm the cable has slack rather than pulling on the shelf.
- Step 6: Inspect the bond regularly; remove the phone immediately if an edge lifts or the wall finish changes.
Mounting surface, stability and environment
Mounting method: single-use 3M adhesive pad on a clean, dry, smooth, flat, sealed vertical surface; press firmly and wait at least 24 hours before loading.
Flat and clean contact. Dust, oil, grit and moisture reduce friction and can scratch surfaces. Clean and dry every contact area before installation.
Keep away from edges. Position the loaded device where a slip or release will not send it onto a person, floor, sink, cooker, keyboard or glass object.
Touch gently. Use lighter taps or support the device for typing, drawing and gaming. A holder designed for viewing is not always a rigid typing platform.
Recheck regularly. Temperature, vibration, repeated adjustment and normal wear can change grip. Inspect the mount, pads and device position before each important use.
Compatible devices and systems
Physical class: most smartphones whose complete phone-and-case thickness is no more than approximately 14mm and that can rest securely across the 117mm-wide shelf.
Apple devices. Compatible iPhone or iPad examples may fit only when their complete size, weight and case remain within the stated physical limits.
Android devices. Samsung Galaxy, Google Pixel, OnePlus, Xiaomi, Redmi, realme and other phones/tablets are assessed by measurements—not brand alone.
E-readers and handhelds. A Kindle, e-reader, Switch or similar device may fit only if all support points engage and the complete device stays inside every size and load limit.
Case caveat. A protective case can increase thickness, move the centre of gravity and cover the charging opening. Measure it installed, not separately.
What this product does
- Creates a compact fixed resting shelf for a compatible phone beside a socket, bed, desk or workstation while a separate cable charges it.
- Uses the documented lp108 wall holder mechanism for hands-free physical support.
- Provides the adjustment: fixed wall shelf with no angle, height, rotation or width adjustment; placement must be chosen carefully before exposing the adhesive.
- Uses the mounting method: single-use 3M adhesive pad on a clean, dry, smooth, flat, sealed vertical surface; press firmly and wait at least 24 hours before loading.
- Protects covered contact areas with the specified silicone, rubber or soft pads; these reduce—not eliminate—the possibility of marks.
What this product does not do
- not a charger, tablet shelf, bathroom wet-area mount or reusable/repositionable adhesive system; removal can mark delicate paint, wallpaper or finishes.
- It does not include MagSafe, wireless charging, a battery, powered USB port or motor unless explicitly stated—which this SKU does not.
- It does not make every phone case, tablet, furniture edge, wall finish, air vent or vehicle compatible.
- It does not guarantee zero wobble during touch, typing, drawing, rough roads or fully extended use.
- It is not safety equipment and should not suspend a device where release could cause injury or serious damage.
What to do
Measure first. Check the complete device and case against every stated size, thickness, opening and load limit.
Adjust with two hands. Support the device or unload the holder before moving a firm hinge, rail, spring arm, clamp or rotating base.
Route cables safely. Leave slack at the connector, avoid sharp bends and keep cables away from hinges, springs, vehicle controls and walking paths.
Inspect the setup. Check screws, pads, clips, clamps, adhesive edges and device seating before use and after relocation or temperature change.
What not to do
Do not exceed limits. Do not guess load capacity, case fit, clamp thickness, vent compatibility or adhesive reuse beyond the values stated here.
Do not force movement. Stop when a hinge, clamp or rail reaches its natural limit. Do not use tools for extra leverage unless the supplied assembly step requires them.
Do not use near hazards. Avoid flames, hot cookware, wet areas, unstable shelves, traffic controls and positions directly above people or breakables.
Do not trust a partial grip. Both device and mount must be fully seated. A phone caught by one hook, a clamp on a rounded edge or a clip halfway onto a vent is unsafe.
Warnings and limitations
Adhesive safety: do not install on textured wallpaper, loose paint, plaster, damp surfaces or valuable delicate finishes. Adhesive is not guaranteed reusable and removal can mark the surface.
Pinch points: keep fingers, hair, cables and loose clothing clear of hinges, springs, telescopic rails and clamp mechanisms.
Heat and moisture: keep the holder and device away from flames, hot cookware, direct heaters, steam, sinks, rain and pooled liquid.
Children and pets: this is not a toy. Keep small hardware and loaded devices out of reach and avoid trailing cables.
Inspection: stop using the product if a hinge loosens, pad detaches, plastic cracks, metal bends, adhesive lifts, clamp slips or vent blade deforms.
Troubleshooting
Device tips forward. Lower the height or arm, tilt the device back, centre it over the support and remove a heavy case/accessory. Stop if the stated fit or load limit is exceeded.
Holder slides or rotates. Unload it, clean and dry contact pads, retighten only as instructed and move to a firmer, flatter mounting point.
Case will not sit fully. Measure total thickness and width. Remove a wallet, grip, battery or rugged case rather than forcing the device into shallow hooks.
Cable does not fit. Try a slimmer compatible connector and route it without tension. The access opening does not guarantee every plug shape or port location.
Hinge feels too firm. Unload the stand and move the joint slowly with two hands. Do not apply oil, heat or extra tools; stop if the housing separates or metal bends.
Mounting surface looks marked. Remove the device immediately. Do not keep tightening or loading the mount; follow the furniture, wall or vehicle manufacturer’s care guidance.
model check before ordering
Match UGREEN SKU 30394, the lp108 wall holder, its fit boundary, mounting method and adjustment mechanism. Similar UGREEN holders can use different hinges, clamp spans, device limits, adhesives or vehicle fittings.
At a glance.
- Brand / SKU
- UGREEN 30394
- Model / type
- LP108 Wall Holder
- Colour
- White
- Primary use
- creates a compact fixed resting shelf for a compatible phone beside a socket, bed, desk or workstation while a separate cable charges it
- Device fit
- most smartphones whose complete phone-and-case thickness is no more than approximately 14mm and that can rest securely across the 117mm-wide shelf
- Adjustment
- fixed wall shelf with no angle, height, rotation or width adjustment; placement must be chosen carefully before exposing the adhesive
- Mounting method
- single-use 3M adhesive pad on a clean, dry, smooth, flat, sealed vertical surface; press firmly and wait at least 24 hours before loading
- Materials
- white rigid holder body, 3M adhesive pad, soft non-slip phone contact areas and a rear cable-winding spool
- Holder dimensions shown
- Approximately 117 × 64 × 14mm
- Maximum phone + case thickness
- Approximately 14mm
- Installation
- Single-use 3M self-adhesive pad
- Curing time
- At least 24 hours before loading
- Cable management
- Integrated rear winding spool
- Built-in charging
- None
- Charging / electronics
- None; passive mechanical holder
- Package contents
- 1 × UGREEN LP108 / 30394 wall phone holder with pre-applied adhesive pad