UGREEN 5–45° Pedestal Phone Stand, White (60343)
Overview
UGREEN 60343 holds a compatible phone above the desk on a compact weighted pedestal for calls, reading, video, recipes and everyday screen reference. fixed-height pedestal with an approximately 5–45° tilting support plate; it does not telescope, swivel or fold flat. The construction is alloy support arm, rugged ABS shell, galvanized base plate and silicone device/base pads. Below: fit, setup, stability and safety boundaries so the product is easy to choose and use responsibly.
- SKU 60343
- Pedestal Phone Stand
- White / silver
- Passive holder
What it does well.
Key features
Holder type. Pedestal Phone Stand. holds a compatible phone above the desk on a compact weighted pedestal for calls, reading, video, recipes and everyday screen reference.
Fit boundary.
Adjustment. fixed-height pedestal with an approximately 5–45° tilting support plate; it does not telescope, swivel or fold flat.
Mounting method. freestanding 105 × 105mm weighted tabletop base with anti-slip feet; supplied threaded parts must be assembled and tightened before use.
Measure before ordering
Phone and tablet names are only examples. Physical compatibility is controlled by screen and body size, total thickness, weight, case shape, camera bump, accessories and the way the device meets the support points.
Measure the complete setup.
Check the support points. Both lower hooks and the padded back surface must contact the device securely. Remove a wallet, ring, battery case or pop-out grip if it interferes.
Choose a stable position. Open or assemble the stand on a clean, flat and level surface. Start with a low, slightly rearward angle, place the device centrally and increase height or tilt only after checking balance.
Test before normal use. Gently tap the screen and check every hinge, clamp, base, adhesive bond or vent clip. Stop if the device creeps, tips, releases or makes the mounting surface flex.
Adjustment and viewing guide
Mechanism: fixed-height pedestal with an approximately 5–45° tilting support plate; it does not telescope, swivel or fold flat.
Adjust unloaded whenever practical. Support the device with one hand, move the mechanism with the other and stop at its natural limit. A firm hinge is normal; forcing it can damage the joint or make the base slip.
Stability principle: raising, extending or moving a device forward increases leverage. Heavier devices should stay lower, closer to the base or clamp, and slightly tilted back.
Use scenarios
Calls and meetings. Raise the camera closer to a natural sightline and keep the device hands-free. Use headphones when privacy or echo control matters.
Video and learning. Place the screen in portrait or landscape for tutorials, online classes, streaming and reference material.
Desk companion. Keep messages, OTPs, timers, music controls or a second-screen reference visible beside a computer.
Recipes and hobbies. Follow instructions with cleaner hands, but keep the holder away from water, steam, oil, heat and unstable counter edges.
Setup and usability guidance
Best practice: Open or assemble the stand on a clean, flat and level surface. Start with a low, slightly rearward angle, place the device centrally and increase height or tilt only after checking balance.
- Step 1: Check the threaded rod, support plate, base and wrench/hardware against the package.
- Step 2: Attach the plate and rod in the illustrated order without cross-threading.
- Step 3: Insert the rod into the base and tighten evenly with the supplied wrench.
- Step 4: Place the assembled stand on a flat level surface and check for looseness.
- Step 5: Set the cradle within its stated angle range, then centre the compatible phone.
- Step 6: Reconnect a separate charging cable only if its plug fits without levering the device.
Mounting surface, stability and environment
Mounting method: freestanding 105 × 105mm weighted tabletop base with anti-slip feet; supplied threaded parts must be assembled and tightened before use.
Flat and clean contact. Dust, oil, grit and moisture reduce friction and can scratch surfaces. Clean and dry every contact area before installation.
Keep away from edges. Position the loaded device where a slip or release will not send it onto a person, floor, sink, cooker, keyboard or glass object.
Touch gently. Use lighter taps or support the device for typing, drawing and gaming. A holder designed for viewing is not always a rigid typing platform.
Recheck regularly. Temperature, vibration, repeated adjustment and normal wear can change grip. Inspect the mount, pads and device position before each important use.
Compatible devices and systems
Apple devices. Compatible iPhone or iPad examples may fit only when their complete size, weight and case remain within the stated physical limits.
Android devices. Samsung Galaxy, Google Pixel, OnePlus, Xiaomi, Redmi, realme and other phones/tablets are assessed by measurements—not brand alone.
E-readers and handhelds. A Kindle, e-reader, Switch or similar device may fit only if all support points engage and the complete device stays inside every size and load limit.
Case caveat. A protective case can increase thickness, move the centre of gravity and cover the charging opening. Measure it installed, not separately.
What this product does
- Holds a compatible phone above the desk on a compact weighted pedestal for calls, reading, video, recipes and everyday screen reference.
- Uses the documented pedestal phone stand mechanism for hands-free physical support.
- Provides the adjustment: fixed-height pedestal with an approximately 5–45° tilting support plate; it does not telescope, swivel or fold flat.
- Uses the mounting method: freestanding 105 × 105mm weighted tabletop base with anti-slip feet; supplied threaded parts must be assembled and tightened before use.
- Protects covered contact areas with the specified silicone, rubber or soft pads; these reduce—not eliminate—the possibility of marks.
What this product does not do
- not for 7.9-inch mini tablets despite the old title and generic body text; no load capacity is verified, and no charging or magnetic function is built in.
- It does not include MagSafe, wireless charging, a battery, powered USB port or motor unless explicitly stated—which this SKU does not.
- It does not make every phone case, tablet, furniture edge, wall finish, air vent or vehicle compatible.
- It does not guarantee zero wobble during touch, typing, drawing, rough roads or fully extended use.
- It is not safety equipment and should not suspend a device where release could cause injury or serious damage.
What to do
Measure first. Check the complete device and case against every stated size, thickness, opening and load limit.
Adjust with two hands. Support the device or unload the holder before moving a firm hinge, rail, spring arm, clamp or rotating base.
Route cables safely. Leave slack at the connector, avoid sharp bends and keep cables away from hinges, springs, vehicle controls and walking paths.
Inspect the setup. Check screws, pads, clips, clamps, adhesive edges and device seating before use and after relocation or temperature change.
What not to do
Do not exceed limits. Do not guess load capacity, case fit, clamp thickness, vent compatibility or adhesive reuse beyond the values stated here.
Do not force movement. Stop when a hinge, clamp or rail reaches its natural limit. Do not use tools for extra leverage unless the supplied assembly step requires them.
Do not use near hazards. Avoid flames, hot cookware, wet areas, unstable shelves, traffic controls and positions directly above people or breakables.
Do not trust a partial grip. Both device and mount must be fully seated. A phone caught by one hook, a clamp on a rounded edge or a clip halfway onto a vent is unsafe.
Warnings and limitations
Pinch points: keep fingers, hair, cables and loose clothing clear of hinges, springs, telescopic rails and clamp mechanisms.
Heat and moisture: keep the holder and device away from flames, hot cookware, direct heaters, steam, sinks, rain and pooled liquid.
Children and pets: this is not a toy. Keep small hardware and loaded devices out of reach and avoid trailing cables.
Inspection: stop using the product if a hinge loosens, pad detaches, plastic cracks, metal bends, adhesive lifts, clamp slips or vent blade deforms.
Troubleshooting
Device tips forward. Lower the height or arm, tilt the device back, centre it over the support and remove a heavy case/accessory. Stop if the stated fit or load limit is exceeded.
Holder slides or rotates. Unload it, clean and dry contact pads, retighten only as instructed and move to a firmer, flatter mounting point.
Case will not sit fully. Measure total thickness and width. Remove a wallet, grip, battery or rugged case rather than forcing the device into shallow hooks.
Cable does not fit. Try a slimmer compatible connector and route it without tension. The access opening does not guarantee every plug shape or port location.
Hinge feels too firm. Unload the stand and move the joint slowly with two hands. Do not apply oil, heat or extra tools; stop if the housing separates or metal bends.
Mounting surface looks marked. Remove the device immediately. Do not keep tightening or loading the mount; follow the furniture, wall or vehicle manufacturer’s care guidance.
model check before ordering
Match UGREEN SKU 60343, the pedestal phone stand, its fit boundary, mounting method and adjustment mechanism. Similar UGREEN holders can use different hinges, clamp spans, device limits, adhesives or vehicle fittings.
At a glance.
- Brand / SKU
- UGREEN 60343
- Model / type
- Pedestal Phone Stand
- Colour
- White / silver
- Primary use
- holds a compatible phone above the desk on a compact weighted pedestal for calls, reading, video, recipes and everyday screen reference
- Device fit
- the current gallery states 4–6.5-inch devices; the cradle depth shown is approximately 12mm, so thick cases and accessories may need removal
- Adjustment
- fixed-height pedestal with an approximately 5–45° tilting support plate; it does not telescope, swivel or fold flat
- Mounting method
- freestanding 105 × 105mm weighted tabletop base with anti-slip feet; supplied threaded parts must be assembled and tightened before use
- Materials
- alloy support arm, rugged ABS shell, galvanized base plate and silicone device/base pads
- Device range
- Approximately 4–6.5in
- Cradle angle
- Approximately 5–45°
- Overall height shown
- Approximately 153mm / 6.1in
- Base shown
- Approximately 105 × 105 × 7mm
- Cradle depth shown
- Approximately 12mm / 0.5in
- Charging / electronics
- None; passive mechanical holder
- Package contents
- 1 × support plate, 1 × threaded support rod, 1 × weighted base and assembly wrench/hardware shown in the gallery