UGREEN LP124 Reusable Cable Fastening Tape, 2m (40354)
Overview
The tape is reusable and adjustable for indoor desk, entertainment and equipment-rack organisation. Because it fastens to itself, it can be reopened without discarding a one-use plastic tie.
- SKU roll length
- listed tape width
- hook-and-loop construction
- opens and re-fastens to itself
What it does well.
Key features
The defining functions of this SKU are separated from assumptions so size, materials, adjustment and intended use remain clear.
- 2m continuous roll can be cut into custom tie lengths.
- Approximately 20mm tape width spreads holding pressure across a cable group.
- Nylon hook-and-loop faces engage each other without a separate buckle.
- Reusable closure can be opened when equipment or routing changes.
- Black low-profile format suits many indoor desk, television and equipment-cabinet runs.
- One roll can create several ties when each planned piece includes enough overlap.
- No sticky-backed mounting adhesive is verified; it is a wrap-around fastener.
Performance and planning
Plan around the complete setup, not a headline alone. Fit, stability and protection depend on the attached device, surface, loading, handling and surrounding conditions.
Holding strength depends on clean hook-and-loop faces, sufficient overlap, cable weight and the direction of pull. Use multiple ties and separate supports for long or heavy runs.
Cut length must cover the bundle plus a generous overlap. A short overlap can peel open even when the tape feels attached at first.
The soft 20mm band helps avoid the concentrated pressure of a narrow plastic tie, but any fastener can damage cable jackets when overtightened.
This is cable organisation, not structural load restraint. It has no working-load, safety-harness or wall-mount rating.
Use scenarios
These examples show practical uses while keeping the compatibility and safety checks elsewhere in this guide in force.
Desk peripherals. Loosely group monitor, USB, audio and charging leads while leaving connector strain relief free.
TV console. Create removable ties at intervals along an indoor media-cable route, keeping ventilation and power adapters uncovered.
Equipment cabinet. Use several labelled or consistently placed ties so a technician can reopen one branch without cutting the entire loom.
Cable storage. Coil a disconnected lead at its permitted bend radius and secure it gently for a drawer or travel pouch.
Setup and usability guidance
Use this sequence for a deliberate first setup. Follow the connected-device maker’s stricter instruction whenever it differs.
- Power down and unplug equipment before reorganising connected leads. Replace any cable with damaged insulation, exposed conductors or abnormal heat.
- Arrange the cable group in its final route with natural bends and enough service loop at each connector.
- Wrap a temporary section around the group, mark a length that permits broad overlap and remove it before cutting.
- Cut squarely with clean scissors away from cables, eyes, children and pets.
- Place the soft side as appropriate against the cable jackets and overlap the hook-and-loop faces without compressing the bundle.
- Add more ties at intervals rather than overtightening one band. Use separate rated supports for the run’s weight.
- Reconnect power, check connector strain and cable temperature, then reopen and adjust any tie that is too tight.
Compatible devices and systems
Compatibility depends on dimensions, mounting interface, mass and physical clearance. A screen-size label or familiar shape is only a starting point.
- Indoor data, audio, video and charging cables whose jackets can tolerate a loose nylon wrap.
- Mains power leads only when their manufacturer permits the routing, the leads remain uncoiled and ventilated, and adapters stay uncovered.
- Disconnected cable coils when the coil respects the cable maker’s minimum bend radius.
- Cable groups small enough for the chosen cut piece to overlap securely without compression.
- Not intended for hanging equipment, anchoring cable trays, fixing objects to walls or restraining people or animals.
- Not suitable as cable insulation repair, heat shielding, fire containment or a sealed outdoor fastening system.
What this product does
These are the product’s supported physical functions when it is selected and used correctly.
- Creates cut-to-length reusable ties from one 2m roll.
- Groups compatible indoor cables while allowing later reopening.
- Provides a broad, adjustable wrap rather than a one-way ratcheting tie.
- Helps keep stored cable coils together when applied loosely.
- Lets a cable layout be changed without cutting a plastic fastener.
What this product does not do
These exclusions distinguish this product from visually similar protective, mounting or cable-management accessories.
Choose by function: If the required task appears in this exclusion list, select a purpose-built product with the needed rating or interface.
- It does not have pressure-sensitive adhesive for sticking to desks or walls.
- It does not repair cable insulation or provide electrical, surge or fire protection.
- It does not carry a structural working load.
- It does not make cables pet-proof, child-proof, waterproof or heatproof.
- It does not replace strain relief, cable clips, trays or floor covers where those are required.
- It does not make tight coils of high-current mains cable safe to energise.
What to do
These habits improve day-to-day usability and help protect devices, cables and surfaces.
- Leave generous hook-and-loop overlap and test the closure before relying on it.
- Use several loose ties along a run instead of one overtightened tie.
- Keep plugs, strain-relief boots, power bricks and ventilation openings outside the wrap.
- Round sharp cut corners if needed and remove loose nylon fibres before use.
- Inspect reused sections for clogged hooks, fraying or reduced grip.
- Use separate rated supports whenever the cable route has significant weight.
What not to do
Avoid these common mistakes even if the product appears to fit.
- Do not tighten until cable jackets flatten or individual leads cannot move slightly.
- Do not use the tape to hang monitors, power strips, tools or other loads.
- Do not wrap damaged, wet or overheating cables to hide the problem.
- Do not bind a plug into a socket or defeat the designed strain relief.
- Do not restrain people, pets, children or safety equipment.
- Do not assume the word self-adhesive means the tape will bond to a wall or desk.
Warnings and limitations
Review these limits before using the product around valuable equipment, power cables, children or pets.
Stop and recheck: Remove the device or disconnect equipment if the setup slips, strains, overheats, becomes wet or no longer matches the use.
- Overtightening can damage cable jackets and transfer strain to connectors.
- Hook-and-loop strength decreases when hooks are filled with lint or when the nylon is melted, frayed or contaminated.
- Bundled power cables can retain heat. Keep them loose and follow every cable and equipment instruction.
- Cut only with the roll removed from live or connected cables.
- Keep loose offcuts away from infants, children and pets; short bands can present entanglement or ingestion hazards.
- No load rating, outdoor rating, flame rating or sticky-back adhesion specification is for SKU 40354.
Check before ordering
Check the complete physical setup before choosing by a product photo or screen-size label.
- The required SKU is 40354 and roll length is 2m.
- A 20mm-wide self-fastening nylon wrap suits the cable jackets and available clearance.
- The application needs cable grouping, not sticky mounting or structural support.
- Cut pieces can include generous overlap without compressing the bundle.
- The route is dry, indoors, ventilated and away from walking paths and hot surfaces.
- Separate supports can carry the cable run so the tie is not load-bearing.
Care and troubleshooting
Use gentle cleaning and change one variable at a time when diagnosing fit, stability or cable-routing problems.
- Open the tie by peeling the end back gradually; do not yank the cable group or use the fastener as a handle.
- Remove lint from the hook side by hand with equipment unplugged. Avoid solvents, heat and ironing.
- If a tie opens, increase overlap, reduce the bundle, add another tie or replace a worn section.
- If cable jackets show compression marks, loosen the wrap and inspect the cables before reconnecting.
- Store the unused roll dry with the end fastened to itself so hooks do not collect debris.
At a glance.
- Product
- UGREEN LP124 reusable hook-and-loop cable fastening tape
- SKU
- 40354
- Roll length
- 2m
- Tape width
- Approximately 20mm / 2cm
- Colour
- Black
- Material
- Nylon hook-and-loop
- Fastening method
- Wraps around a bundle and attaches to itself
- Customisation
- Cut to required tie length
- Reusability
- Can be opened and re-fastened when clean and undamaged
- Sticky backing
- No pressure-sensitive desk/wall adhesive verified
- Environment
- Dry indoor cable organisation
- Working-load rating
- Not verified; not for structural support or suspension
- Electrical function
- None
- Safety exclusions
- Not insulation, flame/heat protection, restraint or cable repair
- In the box
- 1 × UGREEN LP124 black reusable cable fastening tape roll, 2m × approximately 20mm, SKU 40354
No scissors, adhesive mounting bases, separate buckles or labels are identified as included.
Cables, electronics, furniture, tools and rack equipment shown in scenes are not included.
Model facts are consolidated below. Unverified working-load, internal-fit or environmental ratings are not invented.
Only components supported by the current model record or gallery are listed. Connected devices and scene props are not included.
Questions buyers ask.
How long is SKU 40354?
How wide is the tape?
Approximately 20mm or 2cm.
Is it reusable?
Yes. Clean, undamaged hook-and-loop can be reopened and fastened again.
Can I cut it?
Yes. Measure for generous overlap, remove it from the cable route and cut with clean scissors.
Does it have sticky adhesive backing?
No pressure-sensitive wall or desk adhesive is verified. It fastens by overlapping its hook-and-loop faces.
Can it hang a power strip?
No. No structural working-load rating is verified; use a purpose-built rated mount.
Can it repair a frayed cable?
No. Disconnect and replace damaged cables according to their manufacturer.
How tight should the tie be?
Only tight enough to group the leads while leaving jackets uncompressed and connectors strain-free.
Can it be used on mains cables?
Only loosely, with uncoiled ventilated leads whose makers permit the routing. Keep adapters uncovered.
Can it be used outdoors?
No outdoor or weatherproof rating is verified; use it for dry indoor organisation.
Why did a reused tie lose grip?
Check for lint, worn hooks, fraying, insufficient overlap or an oversized bundle. Replace the piece if grip remains weak.
What is excluded from the package?
Scissors, adhesive bases, separate buckles, cables and scene equipment are not identified as included.