UGREEN 3m Cat6 F/UTP Ethernet Extension Cable (11282)
Overview
UGREEN 11282 is a 3m Cat6 F/UTP Ethernet extension lead. Its RJ45 female socket accepts an existing male patch-cable plug, while its attached RJ45 male plug reaches the destination port. It is listed for Up to 1000Mbps (1Gbps) and uses 8 × 26awg stranded pure-copper conductors arranged as four twisted pairs. It extends a physical cable; it does not regenerate, amplify or repeat the network signal.
What it does well.
Key features
Product highlights
3m. Format and length for planning the physical connection.
Up to 1000Mbps (1Gbps). Product capability, subject to the complete host or network path.
RJ45 male → female. The defining connector, protocol or construction detail for this SKU.
One clear job. Adds 3m of physical reach to an existing male RJ45 Ethernet patch cable.
No hidden upgrade. It does not boost, repeat, clean or regenerate an Ethernet signal.
Maximum versus actual: Maximum listed cable mode: Up to 1000Mbps (1Gbps). Current artwork uses a 250MHz Category 6 reference in artwork. The joined channel is governed by the lowest-category cable, weakest junction, slowest port and total installed length.
Choose the right connection
Port and direction check
1 × shielded RJ45 male plug to 1 × RJ45 female inline socket
Ethernet data is bidirectional, but the physical use is specific: plug the existing patch cable into the female socket and insert the extension cable’s male plug into the destination RJ45 port.
Inspect port labels and connector shapes under good light before routing. A physically similar socket may serve telephone, console, management, USB or power rather than the network job described here.
Connection rule: never force a plug and never assume an adapter preserves the same protocol, speed or driver support.
Network performance
Speed, bandwidth and negotiation
A maximum link rate is not the same as measured payload throughput. Protocol overhead, storage speed, CPU load, router processing, remote servers and internet service can all reduce the number shown by an application.
For a useful test, first confirm the negotiated link rate, then run a local transfer between capable devices before testing a public speed service.
Use scenarios
Where it fits
Existing patch lead stops short. Add up to 3m of physical reach without replacing an otherwise suitable male-to-male RJ45 patch cable.
Desk or office move. Reposition a computer, printer or docking station while keeping the female junction supported and accessible.
Hotel or temporary workspace. Bridge a small indoor distance from an existing Ethernet lead to a laptop or compact router.
Console or television setup. Extend a wired connection to a compatible RJ45-equipped console, smart television or media player.
Cable-management correction. Move a junction away from a strained device port, provided the complete channel remains within Ethernet length and performance limits.
Scenario boundary: every example assumes the actual ports, protocol, operating system and network equipment support the requested use.
Setup and usability guidance
A reliable first connection
Follow a controlled sequence so connector, network and software faults remain easy to isolate.
After setup: record the working port, negotiated speed or address configuration before adding more adapters, joins or software.
- Confirm UGREEN SKU 11282, the required 3m reach and an existing male RJ45 patch lead.
- Inspect the female socket, male plug and existing patch-cable latch for damage or debris.
- Insert the existing male RJ45 plug into the extension socket until it clicks.
- Connect the extension cable’s male RJ45 plug to the destination LAN port.
- Support the female junction so it does not hang by either cable and keep it out of foot traffic.
- Check link lights and negotiated speed, then run a local transfer test.
- If performance drops, test each original cable directly and replace the weakest or damaged component.
Compatible devices and systems
Compatibility explained
Compatible endpoints.
Required existing cable.
Channel behaviour.
- Computers, docks and network adapters with RJ45
- Routers, switches, gateways and access points
- Smart TVs, consoles, media boxes and network printers
- A standard male RJ45 Ethernet patch cable
- A cable category suitable for the intended channel speed
- An undamaged latch and clean connector contacts
- Backward compatible with 100Mbps and 10Mbps links
- Maximum 1Gbps only on a suitable complete channel
- No driver or external power required
What this product does
Supported jobs
Use SKU 11282 for these roles.
Each role stays within the product category described above; it does not imply conversion, amplification, routing or software support that is not listed.
- Adds 3m of physical reach to an existing male RJ45 Ethernet patch cable.
- Creates a removable male-to-female inline extension without a separate coupler.
- Supports up to Up to 1000Mbps (1Gbps) on a compatible complete channel.
- Carries bidirectional Ethernet data and allows ordinary auto-negotiation.
- Uses copper twisted pairs and shielded construction described for this SKU.
- Works without a software driver or external power supply.
What this product does not do
Important exclusions
These exclusions prevent the most common wrong-product purchases and unsafe installations.
Choose another product when needed: use the correct active adapter, router, switch, repeater, installation-rated cable or managed service for functions outside this model’s role.
- It does not boost, repeat, clean or regenerate an Ethernet signal.
- It does not add 3m beyond the applicable total Ethernet channel limit.
- It does not convert USB, telephone, fibre or coaxial networking into Ethernet.
- It does not make a slower existing cable or port operate at 1Gbps.
- It does not provide an independently PoE class or wattage.
- It does not have a published outdoor, burial, in-wall or public-space fire rating.
What to do
Best-practice checklist
Protect the connection and make later diagnosis straightforward.
A labelled, supported and tested connection is easier to maintain than one hidden immediately after purchase.
- Use the female socket only with a standard, undamaged male RJ45 patch-cable plug.
- Support the inline junction on a desk, tray or cable-management point.
- Keep the joined channel as simple and short as practical.
- Test the original cable, extension and ports separately if speed drops.
- Leave broad bends at the female housing and the male strain relief.
- Keep the junction dry, accessible and away from heat or moving furniture.
What not to do
Avoid these mistakes
Most failures come from wrong interfaces, unsupported claims, strain or uncontrolled channel changes.
Stop using the product if a connector, housing, jacket or lead is cracked, loose, contaminated, unusually hot or exposes conductive parts.
- Do not leave the female socket hanging from a device port.
- Do not daisy-chain several extensions or couplers when one correct-length cable is available.
- Do not crush, staple, trap or sharply bend the cable or inline socket.
- Do not force telephone or non-RJ45 plugs into the female socket.
- Do not assume the extension increases internet speed or repairs a damaged cable.
- Do not install outdoors or inside a wall without the required documented rating.
Warnings and limitations
Read before installation
The following limits remain important even when the connector appears to fit.
Permanent routes: test the complete real setup first and follow local electrical, building and workplace requirements.
- Every extra junction adds contact points and can reduce channel margin.
- The complete link is limited by the slowest port, lowest-category cable and total channel length.
- The 250MHz figure is the current Category 6 reference used here; a conflicting 550MHz phrase is not relied upon.
- No outdoor, direct-burial, in-wall, plenum, LSZH or fire-resistance rating is stated for this product.
- Stop using the extension if the female housing, plug latch, jacket or strain relief becomes cracked, loose or unusually hot.
- PoE use is not promised because an class, wattage and installation rating are not published.
At a glance.
- Cable category
- Cat6
- Precise shielding
- F/UTP
- Conductors
- 8 × 26AWG stranded pure-copper conductors arranged as four twisted pairs
- Gauge
- 26AWG
- Cable form
- Round; Approximately 6.2mm on this product record
- Connector pair
- 1 × shielded RJ45 male plug and 1 × RJ45 female inline socket with gold-plated contact wording
- Outer jacket
- Black PVC
Physical build
F/UTP construction, 8 × 26AWG stranded pure-copper conductors arranged as four twisted pairs, 1 × shielded RJ45 male plug and 1 × RJ45 female inline socket with gold-plated contact wording, round Black PVC jacket.
What is in the pack
Included only as stated for this current product record.
Routers, computers, printers, network cables, USB adapters, installation hardware and power supplies are not included unless individually listed above. Inspect the retail package before installation.
Questions buyers ask.
Which end connects to the existing cable?
Insert the existing patch cable’s male RJ45 plug into the extension cable’s female socket, then connect the extension’s male plug to the destination port.
Is the Ethernet signal directional?
No. Ethernet data is bidirectional, although the male-to-female physical arrangement gives the extension a specific connection sequence.
Can it support gigabit Ethernet?
It is listed for up to 1000Mbps when the complete joined channel, both cables, every connector and both ports support gigabit.
What bandwidth figure is used for this Cat6 cable?
Does the extension improve a weak signal?
No. It is passive and does not amplify, regenerate or correct an existing cable fault.
Can I join several extension cables?
A single correct-length patch cable is preferable. Each junction adds contacts and length, so daisy-chaining can reduce channel margin and reliability.
Will it work with consoles and smart TVs?
Yes, when the device has a standard RJ45 Ethernet port and the full link is configured correctly. It cannot add Ethernet to a USB-only device.
Does it require software or power?
No. It is a passive copper Ethernet lead with no driver or external power requirement.
Is PoE supported?
No PoE class or wattage is verified, so this page does not promise PoE use.
Can it be routed outdoors or in a wall?
No outdoor, burial, in-wall, plenum, LSZH or fire rating is published for this SKU.
What should I check if the link drops to 100Mbps?
Test the original cable directly, inspect all eight contacts, confirm every port supports gigabit and replace any damaged or lower-category component.
What is included?
One 3m UGREEN 11282 Cat6 male-to-female Ethernet extension cable is listed. A separate original patch cable is required.